|
|||||||||
|
|||||||||
 |
 |
|
|
 |
 |
 |
 |
 |
 |
 |
Sodium Analyzer
Quantichem® 9031C
QUANTICHEM®
9001 COMPACT SERIES
QUANTICHEM® 9001 COMPACT SERIES
The Waltron Quantichem® 9031C Sodium Analyzer is the most advanced online instrument specifically developed for use in continuous measurement and determination of sodium ion concentration. Common 9031C Sodium Analyzer application points in a boiler system for online sodium measurement include:make-up water,condensate,boiler feedwater and saturated steam/main steam. Please contact us for panel mount version. |
|
||
   |
 Spare
Parts Reagents Manuals |
MSDS
Sheets Troubleshooting Start-up Guide |
|
| FEATURES | BENEFITS | |
| • Wide analysis range: 0.1ppb – 10ppm | • Low reagent and standard consumption | |
| • Low maintenance | • Minimal maintenance required | |
| • Very low reagent and standard consumption | • Automatic operation | |
| • No change of diffusion tubing | ||
| • Automatic range selection | ||
| • Process calibration – calibrate to sample | ||
| • Two 4-20 mA isolated current outputs | ||
| • Protection of electrodes from “Hot Sample” | ||
| • Automatic temperaturecompensation | ||
| • Automatically stores last 10 calibrations and alarm logs | ||
| • No use of highly toxic reagents such as monoethylamine or diisopropylamine |
Flow path during calibration mode and normal operating conditions
Quantichem® 9031 Sensor Unit
During calibration the 3-way valve is activated, a standard of known sodium concentration passes through a heat exchanger to equilibrate the solution’s temperature to that of the sample. The standard then enters the constant head unit where flow is stabilized. Alkaline buffer vapor is added via a vapor entrainment mechanism before the standard enters the sodium measuring flow cell and flows to drain. During normal operating conditions the standard solution is replaced by the sample.
| Performance | ||
| Range | 0.01ppb - 10ppm | |
| Accuracy | ±5% of reading or ±0.1ppb (whichever is greater) within ±5°C of calibration temperature |
|
| Reproducibility | ±5% of reading or ±0.1ppb (whichever is greater) at constant temperature | |
| Response Time | 90% of 1-10ppb step: less than 4 minutes; 90% of 100-1ppb step: less than 6 minutes |
|
| Temperature Compensation | Automatic | |
pH Compensation |
Alkaline vapor buffer:0.88 SG (28% to 30% NH3) ammonia above 0.1 ppb sodium,50% diethylamine solu-tion below 0.1ppb sodium |
|
| Single or 2-point Calibration | Manual calibration |
|
| Current Outputs | Two isolated 4-20mA current (analog) outputs | |
| Digital Outputs | Communication interface via RS-232 & RS-485 using MODBUS RTU protocol |
|
| Alarms | Three voltage-free contacts, alarm points set from transmitter rated at 2A, 250VAC (non-inductive) |
|
| Power | Wide range of input power supply 90VAC – 250VAC | |
| CECertification (on request) | Meets low voltage and low electromagnetic compatibility directives |
|
| Operating Conditions | ||
| Sample | Temperature: 41 – 131° F (5 – 55°C); Flow 150 – 400 ml/min | |
| Ambient Temperature | 32 – 131°F (0 – 55°C) | |
| Pressure | 5 – 30 psig (0.35 – 2.07 bar) | |
| Composition | Sample should be filtered to 60 microns,free of film forming compounds | |
| Mechanical | ||
| Construction | Transmitter – high strength ABS,IP65 (NEMA 4x) Wet section – high strength ABS and sheet metal,all wetted parts stainless steel or PVC,IP55 (NEMA 4) |
|
| Dimensions | Transmitter: Height = 10.92” (27.74 cm), Width = 7” (17.78 cm), Depth = 3.54” (8.99 cm) |
|
| Mounting | Four key-style holes: Height = 0.86” (2.18 cm), Top Width = 0.281” (0.714 cm), Radius = 0.28” (0.711 cm) Horizontal: 9” (22.86 cm), Vertical: 12.875” (32.70 cm) | |
| Weight | 23 lbs. (10.44 kg) | |
| Wiring | Eight (8) conduit knockouts | |
| Piping | Sample Inlet: 1/4” (0.635 cm) OD Swagelokt, Drain: 3/8” (0.953 cm) OD tube |
|
| Distance | Up to 325 feet (100 meters) on request | |
| Finish | Corrosion resistant | |
